Good people!
I am trying to add a subreport to the main report and it must be repeated on each page. I already try to put the "RepeatWith", but it is not allowed to subreport.
Also try to add it as header to the "tablix", with the "RepeatOnNewPage", but it repeats it without regenerating the information (DataSet) of the subreport itself, leaving literally the same.(Because I take it as "Static")
Any other idea?
Related
I have a crystal report in VS19 where I want to move my entire report footer to the last page if the report have multiple pages. Currently what is happening is, if my report have multiple pages, report footer will appear in the 1st page itself and accommodate as much of controls it can there and move the rest of the section to the last page. I have tried a lot of things such as adding formula to suppress the report footer if
pagenumber <> totalpagecount
then tried adding new page before with the same above formula. but nothing was working properly. If i applied new page like this it will forcefully make the reports 2 paged which is actually not needed and behave according to the formula. What I exactly needed is , if the detail section has more data such that it will make the report overflowing to make it 2 paged, then only the entire Report Footer should appear in 2nd page/last page. Could anybody help me. Thanks in advance.
In Section Expert for report footer section, turn on the Keep Together checkbox.
So, I have a report that shows data in a grouped format. All great.
I want to now add 1 extra page to the end of the report which has some data being passed as a parameter (dynamic image in this case).
How can I get the RDLC to add 1 page after all the other data has been rendered just to show this extra bit of information?
The same question applies to a "Page of contents"/index too so pages at the beginning of the main report.
If I understand correctly you can:
add a Rectangle after your Table and set its .PageBreakAtStart
property
use this Rectangle as a container for your Image control
Did anyone found the solution to this problem?? Subreport inside Details section gets repeated.
Is there a way to display subreport only once? I don't want to put it in header.
Please help guys,.
The easiest way is to not put the subreport in the details section. You can create a new section that has no automatic iteration in it and just use that. Or you could put it in the report header or footer.
I have a rdcl ready to be populated.
It mainly contains a table that occupies the whole width and a few Textboxes under it that show summary info.
Sometimes the table will have a lot of lines and other times only a couple of them. This makes the texboxes to end up in the same page or a 2nd (or a 3rd) depending on the situation.
I wanna know if it is possible to so specify a jump to the next page for the textboxes.
So for example even if the table has only 1 line, and there is enough space under it to fit the texboxes info in 1 page, i want them to start at the 2nd page. And if the table is too long and occupies 1 and a half pages, the textboxes should appear in the 3rd page, and so on.
I thought of creating a 2nd report with only the textboxes but then the page numbers do not match and also the reports are showed in different windows.
Any pointers are most welcome.
As far as I know, if the report objects exits on the same rdcl you can not send them to a certain page.
You can, however, alter the "PageBreak" option on the Table to "End". This will push everything after the table onto the next page.
This will help you get the desired results you are after.
EDIT:
You could also get rid of the numerous pages all together by changing the Report property "InteractiveSize" to a height of lets say 50in. This causes the report viewer to page break much less often (every 50 inches) and would most likely place all of your content on Page 1 in the report viewer.
I'm creating some report in C# and I have 2 types of them. The header and footer are the same but the middle part is different. I have a type parameter to determine which type report is it. But I don't know how to change the source subreport. The field "Use this report as subreport" unfortunately doesn't allow to enter the expression so I cannot define the necessary report by condition. And I don't know how to do that from the code.
I've found the solution. Just put 2 different subreports on the main report and use expression to determine which one should be shown, which - to be hidden. Stupid but works.